|
|  |
| Classifieds
- FOR SALE or TRADE, WANTED |
|
Items
listed free to private sellers for 60 days.
Ads dropped 60 days
after posting unless we hear different from you. Email
classifieds@hobbsmotorsportspark.com
with the ad text and any photos -
we'll get it up soon as we can. Be sure you include your
contact information.
Please note that the items listed are for sale by
individuals. They are shown here for informational purposes
only and Hobbs Motorsports Park implies no guarantees or
warranties as to the condition of these items. Ads reserved
for race related items, cars and parts please. |
|
 |
 1982
Pontiac Firebird
–
· Engine
- Sunset Racecraft 555 - Merlin II Block -
JE Pistons, JE rings, Childs & Albert Rods,
Cola Crank, Brodex 2 Extra Heads, Crower
Lifters, Lunati 50222 cam, Comp springs, Comp
rockers, stainless steel valves, MSD
distributor, Moroso 3 vane vacuum pump, Meziere
52 gal electric water pump, 35 amp alternator,
front and mid plates, CVR starter, Ed Quay
competition headers,
·
Transmission
- Footbrake Powerglide - ATI MRT 8in. converter,
ATI 1.80 straight cut planetary, extra large
band, governor support needle bearing, oversize
case bushing, 8 Kilgore Effect High Clutches
with Kolene steels, ATI input shaft, pump/high
gear drum needle bearing, ATI stator support
·
Front Suspension
- Koni adjustable struts, Eibach coil over
springs, Wilwood calipers, 3/8 cast iron rotors,
Pinto rack and pinion
·
Rear Suspension
- Strange Nodular Case, 4.86 gears, Strange 40
spline 5 X 5 axles, Dual Wilwood Calipers with
3/8 cast iron rotors, Strange 1350 yoke, Hal
double adjustable shocks, Lamb Springs, S & W
4-link
·
Fuel System
- 5 gallon aluminum fuel cell, Magnafuel 500
pump, ¾ in braded fuel line to carb, Magnafuel 2
port regulator, APD custom Dyno calibrated 1190
Demon carb
·
Interior
- Jaz pro stock seat, RPM Data Acquisitions,
3 in oil pressure and temp gauge, vacuum gauge,
trans temp gauge,
·
Chassis
- S & W back half with Chromoly front half.
Dual batteries in rear. With 190 pound driver
car scales perfect in rear.
·
33x16.5x15 MT slicks on ProStar
14 in wide rims, 29x4.5x15 MT on ProStar 4 in
wide rims
·
Immaculate records were kept of
exactly how many passes on car, lifters, tires,
input shaft, gears, etc., etc.
·
81 passes on engine rebuild with
new pistons, rings, valves, bearings, cam,
lifters, springs, gaskets, etc.
·
Runs consistent low 9.30’s at
Texas Motorplex, Ennis, TX
REDUCED Asking $18,000 $15,000 OBO Print
Data/Spec Sheet
Coy-82Firebird.pdf
Contact:
Coy in Floydada, TX at 806-269-5358 at email
coyfra@caprock-spur.com
(20130307) |
 |
1975 Chevy Monza
Body: Don Ness Chrome Moly Chassis Not
Certified For The Past 4 Years, Will
Certify To 8.50 , Lamb Front Struts (Need
Rebuilt), Lamb Front And Rear Brakes, New Front
Lamb Springs, Seat Belts Good Through 2012,
Lexan Windows, Fiberglass Front End, Doors and Decklid, Parachute, 2 New Optima Batteries,
Wheelie Bars, Three Link Rear Set Up, Air
Brushed Dash,
Engine: 360 Cu Small Block Chevy, Dart
Aluminum 230 Ported And Polished Heads, Lunati
Roller Cam .645-.630 Lift, Comp Cams Roller
Rockers, Eagle 4350 Steel Crankshaft, Eagle Rods
I Beam, SRP Pistons, 14.7:1 Compression, Msd
7al2 Ignition, Mr Bigs 950 CFM Carb, Dedenbear
Throttle Stop, Dedenbear Crossover Box,
Dedenbear Aluminum Water Pump, Aluminum
Radiator, Moroso Vacuum Pump,
Drivetrain: New Powerglide With BTO Gears
(30) Passes, Programmable Electric Shift, Coan
5500 Stall Converter, BTO Trans Brake, Dana 60
With 5.36 Gears For 1/4 Mile, Summers Brothers
Axles, New Mickey Thompson 32x14.5 Slicks And
Front Runners About (20) Passes,
Weighs 1976 Pounds With Fuel And Batteries, Car
Runs Mid 9's At 4400 Feet In The 1/4 Mile And
Low 6's In The 1/8 Mile, Was On SPEED Channel
(Pass Time) In Roswell Dragway (NM), and
Amarillo Dragway (TX). See On YouTube Video,
Search For (Eldon Russ) 3 Videos. Asking $18,500
obo,
Contact: Eldon in Clovis, NM at (575)
714-1483 or
eldon.russ@gmail.com (032312)
|
 |
421 cu.
in. smallblock. little M. block splayed caps
on all 4,calles 3.875 stroke crank ,eagle 6"
rods with L19 bolts, diamond 15/1 pistons with
total seal low tension gapless top rings, dart
230 platinum heads fully ported, super victor
intake,1000 cfm pro systems acho. carb, crs
water pump, moroso vacuum pump, moroso 7 quart
pan with hvd oil pump, cloyes hex adjust true
roller timing chain with cloyes alum cover,
comp. roller cam and lifters, roller rockers and
stud girdle, alum. valve covers, motor has about
700 hp. ran 5.22 in 1800 lb dragster at 2600 ft.
Asking $8000.00
Contact: Lewis at (432)638-0292 or
lcleveland@grandecom.net (032212) |
|
|
1980's 454
Big block chevy with two bolt main, low
mileage, Edelbrock Performer Airgap, HEI
distributor, does not have an oil pan. $600 obo
1997 Vortec 5.7 disassembled short block,
includes all the roller cam components, one
piece rear main seal, 2 bolt main, $150 obo
1998 Vortec 5.7 heads, all stock and
assembled, $250 obo
1988 5.7 short block, (flat tappet cam,
but has all the provisions in the block for an
OEM roller cam) the engine came from a one ton
cab and chassis, one piece rear main seal, 4
bolt main, $150 obo
1989 700R4 transmission, lokar floor
shifter, upgraded clutches, shift kit, corvette
servo, 5,000 miles since rebuild-$650 obo
Misc. Parts.
1 serpentine setup with all accessories-$100
obo, 1 serpentine setup w/o alternator-$75,
Edelbrock 1405 Carb-$150 obo, GM Mini torque
starter with bolts-$50 obo,
Other parts available Holley sbc intake (non
vortec), misc alternators, misc a/c compressors,
misc starters.
Only trades I'm interested in is a vortec 5.3 or
6.0, 4l60E (LS motor) or 4l80E transmission, t56
transmission for LS motor
if you are interested in multiple items a
package deal can be made.
Contact: Jesse at (580) 302-2423 in
Hobbs, NM or
jessegreenfield@sbcglobal.net
(032212) |
 |
2000
Firebird Top Sportsman car,
Has never
finished outside top 10 in division 4 and has
finished #9 and #4 in National points in the
IHRA. Certified to 6:00’s, add your motor &
trans and go racing, Carbon Fiber drive shaft,
race pac, new back tires (4 passes), CC3, 4:30
gear, MW gun drilled axels, Carbon Fiber breaks
front and rear, Headers, front mount fuel cell,
$35k OBO, More pics, available on request
Contact: Kevin Or Scooter at
khampton@frontierfieldservices.com
or 806-663-1929 or 432-301-0064 (092811) |
|
NO PHOTOS |
1 set m/t
13.5x29.5x15 drag slicks new $400,
1 set m/t 12.2x31.25x15 drag radial like new
$500,
1 set weld wheels 15x12x5.5 rear 4.5-4.75 bolt
pattern $350,
1 set 15x14x7.5 rear 4.5-4.75 bolt pattern $400,
1 set 15x14x6.5 rear 4.5-4.75 bolt pattern $250,
1 set 15x3.5x1.75 rear 4.5-4.75 bolt pattern
$250,
Contact: Bill in Roswell, NM at 575-623-1988 or
bcallawayjr439@gmail.com (092811) |
|
|
|
|
|
